Picking The Right Nail That Everyone In The Industry Should Know

Picking The Right Nail That Everyone In The Industry Should Know

Pneumatic nail are extremely light and efficient and drive fasteners that can be operated with flexibility and precision, which makes them perfect for a wide range of purposes. With a variety of options available choosing the right tool and fastener combo can seem like a difficult job.

To make it easier for you to decide to help you make the right choice, here are some general guidelines and the distinctions to be considered when selecting a fastener.

Every masonry fixings and size has its pros and cons as well as being the most suitable to specific tasks. For indoor use that rank from smallest to the largest gauge. Here are a few advantages:

23-gauge – Used for small stained or sheradised nails (typically used to hold the materials to each other while adhesive sets cures)

21-gauge – Ideal for small stained or painted mouldings as well as small-sized casings or chair rails (provides the same appearance as 23 gauges, but with the 80% holding capacity that is comparable to an 18 gauge)

18-gauge – For medium-sized or small-sized casings. Also for chair rails, or crown mouldings with low-profile

16-gauge – Used for the nail that is on the outside of casing (through the drywall) as well as for base trim and other large trim

15-gauge – For the nail that is on the outside of the casing (through the drywall) as well as for base trim or any other trims, and for the solid installation of door jambs, especially strong, solid-core doors.

Interior applications that are not structural like crown moulding door casings, chair rail give you the best choice in the fasteners and tools that you can use.

For structural fastening, such as sheathing, framing, or plate connection, the majority of fasteners are governed by the code or architectural specifications. The manufacturer of the substrate might designate specific fasteners to use with their products.

Sometimes, plans have a nail size of 6D with the “d” signifying pennyweight. This is a long-standing holdover from the days when nails were sold in a quantity of 100 per size of nail. Nowadays the “d” is how long the nail is.

There are other instances where plans require a 6-d Common nail. This is an additional degree of accuracy that will include the size of the shank of the nail in comparison to a conventional box nail. The most significant difference between ordinary nail and box nails lies in the thickness of wire used to make the shank.

The common dome head rivet is made from the heavier gauge wire, which is typically around 5/32″ thick. They’re typically used for home framing in areas where strength is essential. Box nails have shanks that are thinner in gauge — about 1/16″ which are perfect to secure non-structural items such as trim, shingles and siding. The thinner gauges are less likely to break the wood.

Some plans may require the use of a particular measurement, or diameter. The greater numbers, the less the nail. The smaller the number, the larger the nail.

Degrees Of Difference Framing Nail Gun Angles

Degrees Of Difference: Framing Nail Gun Angles

Wire coil, clipped head or plastic strip. Framing nail guns are available in a myriad of collations and types. Are you wondering what’s the deal with the various angles for framing nailers? Don’t be concerned. From 15-degrees to 34-degree nailers. We’ve got you covered. angle for framing guns.

The first thing to remember is the fact that angle degrees are related to the collation of the nail, not the slant at which nails are driven. Nails are driven perpendicularly or straight to a surface. The other thing you need to be aware of is the degree of framing nailer that you require could be contingent on the geographical area of your project. We’ll get to that later.

15-Degree Framing Nailers

There are two primary types of framing nailers: coil and stick collation. All nailers that are part of the 15-degree range can be wire-coil colluded. The nails are held in place by two thin wire strips; they are slanted at an angle of 15 degrees.

The nail itself has a full-round head and the collation has a circular shape. Most of the time the full-round-head nail drives these nailers is the one that is recommended to meet building codes. 

The major benefit of a frame nailer that is a coil design is that it is able to access the floor joists, wall studs and narrow corners that are common when framing. Another benefit is the number of fasteners that the magazine can carry.

Its concrete nails (formerly Hitachi) NV83A5M (shown above) is an example, as it holds up to 300 nails. This means there’s less stopping to refill which is ideal for long-term work. Another benefit is that the collation made by wire coils isn’t as severely affected by moisture as is the collation of paper. When you’re working in a humid environment, this is a huge advantage.

Frame Nail Guns 21 Degrees

This kind of frame nailer magazine angle usually can vary between 20-22 degrees, depending on the maker of the product. The three-degree difference gives the user some flexibility in the choice of angle. Like the 15-degree coil nailers, the 21-degree framing nailer uses an all-round head nail. The main difference is the collation style that has nails joined with a plastic strip, in contrast to wire coils.

The strip of plastic that holds the nails in place is broken after firing the nail. It is possible that there will be tiny pieces of plastic flying away, and you should wear protective glasses when using them. There may also be tiny bits of debris scattered around the area where you work, and may require cleanup.

28-Degree Framing Nailers

In contrast, 28-degree framing nailers are joined with wire strips. The nails are either full-round offset heads, or clipped-head. To make sure magazines aren’t cluttered and make smaller tools the collated nails of the 28-degree frames are “nested” close to each other which means that their heads cross someplace.

This Bostitch F28WW frame nailer (above) holds 100 nails and can drive 2″ to 3 1/2″ framing nails which are collated wire strips. Certain building codes don’t allow offset-head or clipped head type nails, so be sure to verify first before purchasing.

30 Degree Framing Nailers

These nail guns for framing are in a range of angles from 30 to 34 degrees. The angle being the highest gives the most accessibility to angles that are tight in framing tools. A well-known framing nailer for this category includes the FramePro 325XP from Senco illustrated above, which is able to drive the 2″ or 3-1/4″ strip nails made of paper.

Final Note

In construction, some regions of the country might require a particular framing nail collation or head type in order to meet the building codes. If you live in areas with more extreme weather conditions (hurricanes for instance)

The codes typically require a full-round head nail, which comes with more pull-through resistance. Be sure to verify the local building codes to determine what type of nail you need prior to buying.

Be sure the nails you purchase are in line with the wire gauge specifications of the manufacturer as well as length requirements. Certain nailers state that you are only allowed to use the specific nail of the brand. There might be some truth in this, based on the kind of driver blade the nailer uses.

Drivers are available in triangular, crescent or T-shaped types of drivers. However, the majority of nail guns can be used with other types of nail without problem, as long as the nail’s size and collation are in line with the specifications of the tool.

Leave a Reply

Your email address will not be published. Required fields are marked *